Support & user guides

Bluetooth® technology will enable the user to link a compatible phone or device to the vehicle for hands free operation. Your Bluetooth® capable phone or device must be inside the vehicle for it to connect to the vehicle system. Select your phone manufacturer from the selection below to check compatibility.

Audio - Step by Step Instructions

Step 1
The Holden MyLink system is able to store up to 36 favourite AM or FM stations. To set a favourite, first select either the AM or FM band.
Step 2
Tune the radio to the station you wish to set as a favourite. This can be done by touching the menu icon on the touchscreen and selecting from the station list by touching your choice.
Step 3
If you use the SRCE button to select the band, you can tune to the station by turning the MENU/SEL dial to find the station you want then press the button to select it. Alternatively you can use the double arrow right and left buttons on the centre console to search for the next station.
Step 4
Once you have tuned the radio to the station you wish to set as a favourite, press and hold either a preset button on the centre console or one of the preset icons on the bottom of the touchscreen. After a few seconds, a beep is heard confirming that the station is locked into that position.
Step 5
Repeat for each preset. Note: Autostore searches and stores AM and FM stations with the strongest signal. This gives you access to more stored stations. Refer to owner's handbook to activate this function.

Was this helpful?

No Yes
Step 1
Activate Bluetooth® settings^ on your compatible mobile device# and select the option that makes the handset 'discoverable'.
Step 2
Press the CONFIG button on the centre console and select phone settings. Select Bluetooth® then pair device from the menu and the system will display a pairing code that you may need to enter on your phone or device.
Step 3
Start the pairing process on your phone or device and select MyLink from the list that displays on your phone or device. Depending on the device, you may now need to enter the pairing code to complete the process.
Step 4
If your device or phone prompts to 'accept connection' or 'allow phonebook download', select 'always allow' or 'allow'.
Step 5
The Holden MyLink system allows up to five devices to be paired but only one can be connected at any one time. * The Bluetooth® word mark and logo are registered trademarks of Bluetooth® SIG, Inc. ^ Touching your phone while driving is illegal. Make sure that Bluetooth® is activated before driving. If not stop at a safe place to use a mobile phone. # Not all phones will support all functions. For more information visit: www.holden.co.nz.

Was this helpful?

No Yes
Step 1
Ensure your phone or compatible Bluetooth® device is connected to the MyLink system.
Step 2
Bring up the homepage on the MyLink system and touch the Bluetooth® icon on the screen. Alternatively press the SRCE button on the centre console or the SRC thumb wheel control on the steering wheel until Bluetooth® is selected.
Step 3
Music from your device can be controlled through the icons on the touchscreen or using the SRC thumb wheel control on the steering wheel to skip to the next or previous track.
Step 4
* The Bluetooth® word mark and logo are registered trademarks of Bluetooth® SIG, Inc. ^ Touching your phone while driving is illegal. Make sure that Bluetooth® is activated before driving. If not stop at a safe place to use a mobile phone.# Not all phones will support all functions. For more information visit: www.holden.co.nz.

Was this helpful?

No Yes
Step 1
Connect your iPod®, iPhone® or USB drive to the port located in the centre console with a USB cable.
Step 2
Once the MyLink system has read the data from your iPod®, iPhone® or USB drive, the system will automatically begin playing the song selected on your device. Where possible, Gracenote technology embedded into the MyLink system will display information such as song, artist, genre and cover art on the touchscreen.
Step 3
Depending on the device, other controls for selecting playlists, artists, albums, songs or genres may be available on the touchscreen or you may be able to use the MENU/SEL dial to control and select such items.
Step 4
If you are listening to another audio source, you can return to the USB page by touching the USB icon on the MyLink Home page or by pressing the SRCE button on the centre console or the SRC thumb wheel control on the steering wheel until USB is selected. * iPod® and iPhone® are registered trademarks of Apple Inc. ^ Due to differences in phone or device hardware and software some users may experience communication issues between their device and the MyLink system that can leave the connection unresponsive. These issues can be resolved by simply disconnecting and reconnecting the cable to the phone or device, or resetting your device.Not all phones will support all functions. For more information visit: www.holden.co.nz.
Step 5
 
 

Was this helpful?

No Yes
Step 1
Plug a single pin 3.5mm cable into the headphone outlet of your portable music device and connect it to the AUX input located in the centre console.
Step 2
The MyLink system will automatically switch to AUX mode once it is connected. If you are listening to another audio source, you can return to the AUX page by touching the AUX icon on the MyLink homepage or by pressing the SRCE button on the centre console or the SRC thumb wheel control on the steering wheel until AUX is selected.
Step 3
You are able to control the volume of your music device through the MyLink system but all other functions need to be controlled through the music device.

Was this helpful?

No Yes

Audio - FAQs

MyLink supports most smartphones and MP3 players that can be plugged in via the USB port. It also supports many different brands of USB flash drives.
MyLink supports song file formats, including .mp3, .wma, and .ogg file name extensions. iPod® and iPhone® are also supported.
It is recommended that iPhone® be connected by USB cable to obtain the best functionality and performance.
MyLink can recognize up to five different Bluetooth® enabled devices.
It will recognise the devices in the order in which they are listed on screen. If a device listed isn’t in the vehicle, MyLink will recognise this and immediately pair with the device that is in the vehicle
Simply access your settings to see the list of different paired devices. Scroll through the list to find the device you’re looking for. Alternatively, you can also press the “Push to Talk” button and say “Change Phone”.
Gracenote Technology is embedded into the Holden MyLink system and identifies the music you are playing via a USB connection or Bluetooth® audio streaming. Information such as the song title, artist, album, genre and cover art are displayed on the MyLink screen.

Phone - Step by Step Instructions

Step 1
Activate Bluetooth® settings^ on your compatible mobile device# and select the option that makes the handset 'discoverable'.
Step 2
Press the CONFIG button on the centre console and select pone settings. Select Bluetooth® then pair device from the menu and the system will display a pairing code that you may need to enter on your phone.
Step 3
Start the pairing process on your phone or device and select MyLink from the list that displays on your phone or device. Depending on the phone, you may now need to enter the pairing code to complete the process.
Step 4
If your device or phone prompts to 'accept connection' or 'allow phonebook download', select 'always allow' or 'allow',
Step 5
The Holden MyLink system allows up to five devices to be paired but only one can be connected at any one time. * The Bluetooth® word mark and logo are registered trademarks of Bluetooth® SIG, Inc. ^ Touching your phone while driving is illegal. Make sure that Bluetooth® is activated before driving. If not stop at a safe place to use a mobile phone. # Not all phones will support all functions. For more information visit: www.holden.co.nz.

Was this helpful?

No Yes
Step 1
Bring up the Home menu on the MyLink touchscreen and touch the Phone icon or press the push to talk button on the right hand side of the steering wheel.
Step 2
Press enter number on the touchscreen then enter the phone number you wish to call on the touchscreen keypad.
Step 3
Once you have entered the number, touch ok on the touchscreen to start dialling.
Step 4
To finish a call there are three options. Touch the hang up icon on the touchscreen, rotate the MENU/SEL dial on the centre console to select hang up and press the dial to finish, or press the Mute/End Call button on the right hand side of the steering wheel. Warning: When driving the vehicle, be sure to keep the volume of the unit set low enough to hear sounds from outside the vehicle (e.g. road and traffic conditions). Not all phones will support all functions. For more information visit: www.holden.co.nz.

Was this helpful?

No Yes
Step 1
Bring up the home menu on the MyLink touchscreen and touch the phone icon or press the push to talk button on the right hand side of the steering wheel.
Step 2
Touch the phone book icon and select the letter group for the name you wish to find. Scroll through the names to find the one you want and touch the name on the touchscreen.
Step 3
Touch the number on the touchscreen and the number will begin dialing.
Step 4
To finish a call there are three options. Touch the hang up icon on the touchscreen, rotate the MENU/SEL dial on the centre console to select hang up and press the dial to finish, or press the Mute/End Call button on the right hand side of the steering wheel. Warning: When driving the vehicle, be sure to keep the volume of the unit set low enough to hear sounds from outside the vehicle (e.g. road and traffic conditions). Not all phones will support all functions. For more information visit: www.holden.co.nz.

Was this helpful?

No Yes
Step 1
Bring up the home menu on the MyLink touchscreen and touch the phone icon or press the push to talk button on the right hand side of the steering wheel.
Step 2
Touch the call lists icon and select from the Incoming Calls, Outgoing Calls, or Missed Calls lists. Scroll through the names or numbers to find the one you want and select it.
Step 3
Touch the call icon on the touchscreen and the number will begin dialling.
Step 4
To finish a call there are three options. Touch the hang up icon on the touchscreen, rotate the MENU/SEL dial on the centre console to select hang up and press the dial to finish, or press the Mute/End Call button on the right hand side of the steering wheel. Warning: When driving the vehicle, be sure to keep the volume of the unit set low enough to hear sounds from outside the vehicle (e.g. road and traffic conditions). Not all phones will support all functions. For more information visit: www.holden.co.nz.
 

Was this helpful?

No Yes
Step 1
Press the Push to Talk button on the right hand side of the steering wheel. The system will respond by saying 'Please Say a Command' followed by a beep.
VF MylinkApps Voice Control
Step 2
Say Dial or Call.
Step 3
Say the entire number you wish to call without pausing followed by the word Dial. Alternatively, say Dial or Call and name of the person you wish to call, for example 'John at Work' and the system will find the number and begin dialling.
Step 4
To finish the call press the Mute/End Call button on the right hand side of the steering wheel. Warning: When driving the vehicle, be sure to keep the volume of the unit set low enough to hear sounds from outside the vehicle (e.g. road and traffic conditions).
 
Warning: When driving the vehicle, be sure to keep the volume of the unit set low enough to hear sounds from outside the vehicle (e.g. road and traffic conditions). Not all phones will support all functions. For more information visit www.holden.co.nz. The Bluetooth® word mark and logo are registered trademarks and are owned by the Bluetooth® SIG, Inc. Touching your phone while driving is illegal. Make sure that Bluetooth® is activated before driving. If not stop at a safe place to use a mobile phone.

Was this helpful?

No Yes
Step 1
Siri is available on a number of Apple iOS products and can be used in an Eyes Free; mode through the Voice Control system on your Commodore. Siri can be used to make and receive phone calls, select and play music, read out and compose text messages, find calendar information and more.
VF MylinkApps Voice Control
Step 2
Ensure your phone has Siri and it is activated. Press and hold the Push to Talk button for three seconds on the right hand side of the steering wheel to activate Voice Control.
Step 3
Once you hear the Siri tone, say a command. While in eyes free mode, Siri will not provide answers that require displaying a web page. For a full list of Siri commands refer to the Apple website. 
Step 4
To exit Siri, press the Mute/End Call button on the right hand side of the steering wheel.
 
* Touching your phone while driving is illegal. * Personal mobile phone data plans are used to access these Apps and data rates apply. Certain mobile phones or devices may not be compatible. Visit the Owners Info section of www.holden.co.nz for a list of compatible devices * Available in Beta only on iPhone® 4S, iPhone® 5, iPad® (3rd and 4th generations), iPad® mini and iPod® Press (5th generation), and requires internet access. Siri may not be available in all languages or in all areas, and features may also vary by area. Data charges may apply.
 

Was this helpful?

No Yes

Phone - FAQs

Most phones are compatible for details of compatible phones visit: www.holden.co.nz. Refer to the tutorial section of this site for more information.
You can find a compatible phone list at www.holden.co.nz in the vehicle owners section.
Check your mobile device operator’s manual for information, to switch on “discoverable mode”. Repeat the steps in the tutorial.
MyLink allows you to pair up to five different devices. These can be smartphones or other Bluetooth® enabled phones and even Bluetooth® enabled devices, such as an iPod® Touch.
While the Holden MyLink system has highly accurate voice-control software, it recognises a list of many commands as well as most names. However, at times there could still be names or words that the system cannot recognise.
Slowing your speech down can assist. If this still does not work, you can use the “Digit Dial” voice command. This allows you to speak numbers one at a time or in groups. For instance, you can say, “Digit Dial” and MyLink will instruct you to say one number at a time. This is the most accurate way of dialling with voice control.
If your phone fails to pair successfully with the system, turn your phone off. After a few seconds, turn it on and restart the pairing process.
Some vehicles may not be equipped with the Voice Control functionality. Please contact an authorized Holden Dealer for further information.

Vehicle Operations - Step by Step Instructions

Step 1
To unlock the doors or boot, you only need to have the remote control electronic key on your person outside the car and be within about one metre of the relevant door.
Step 2
To unlock the car, simply press the button on the door handle and pull the handle to open the door. To unlock the boot, press the touch pad under the boot lid moulding.
Step 3
To lock the doors upon leaving the car, press the button on the door handle or the button on the remote control electronic key.
Step 4
The electronic key can be configured to unlock only the driver's door or all doors when you press the button on the door handle or the electronic key. These settings can be changed through the car's driver information centre and info-display on the centre console.
Step 5
To change the settings for the Remote Lock/Unlock/Start press the CONFIG button on the centre console and use the MENU SEL knob to scroll through to vehicle settings. Press the dial to select vehicle settings then select Remote Lock/Unlock/Start and follow the prompts.

Was this helpful?

No Yes
Step 1
To start the engine, the key must be inside the vehicle.
Step 2
For automatic transmission models, make sure the transmission shift lever is in Park (P) or Neutral (N) and depress the brake pedal. Then press the START/STOP button on the lower dash to the left of the steering wheel to start the car. A green LED in the button will be illuminated.
Step 3
For manual transmission models, depress both the brake and clutch pedals at the same time as pressing the START/STOP button on the dash. A green LED in the button will be illuminated and the engine will start.
Step 4
To stop the engine when the car is stationary, press the START/STOP button on the dash.
Step 5
To use the accessory power mode, press the START/STOP button without depressing the clutch and/or brake pedal. In this mode, a yellow LED in the START/STOP button is illuminated and it releases the steering wheel lock and allows some electrical functions. Note: The diesel particle filter warning illuminates for a few seconds after the engine is switched on if it requires cleaning.

Was this helpful?

No Yes
Step 1
If the battery of the electronic key is weak or the remote control fails, you can use the mechanical key to unlock the driver's door only. Press the button on the remote control to release the mechanical key.
Step 2
Place the key into the lock in the driver's side door handle and unlock the door. You can now open the door using the door handle. To unlock and open other doors, pull twice on the relevant interior door handle.
Step 3
To start the engine, place the electronic key over the small circular cover in the bottom of the cupholder in the centre console with the Holden logo facing upwards. Depress the brake and/or clutch pedals and press the START/STOP button.
Step 4
To stop the engine when stationary, press the START/STOP button for at least two seconds.
Step 5
To lock the car when leaving, lock all doors except the driver's door using the inside locking knob. Once outside the car, close the driver's door and lock it using the mechanical key in the lock on the door handle.

Was this helpful?

No Yes

Vehicle Operations - FAQs

Sensor Key Technology is a keyless entry and start system that allows you to unlock and lock the car and start and stop the engine without having to physically use the remote control electronic key. You only need to have the key on your person and be within about one metre of the relevant door that you wish to unlock.
With the key in your bag or pocket, unlock the car by pressing the button on the door handle and pull the handle to open the door.
The remote control electronic key can be configured to unlock all doors or only the driver’s door when you press the button on the door handle. To find out how to change the settings, refer to your owner’s manual.
The Sensor Key system has a manual override if the battery is weak or the remote key is not working. Press the button on the key fob to release the mechanical key and place it into the lock on the driver’s side door handle to unlock the car.
Place the remote control electronic key over the small circular cover in the bottom of the cupholder in the centre console with the Holden logo facing upwards. Depress the brake and/or clutch pedal and press the START/STOP button. To stop the engine when stationary, press the START/STOP button for at least two seconds.
No, to lock or unlock the car using the Sensor Key system, the key must be outside the car.

Bluetooth® Wireless Technology:

Bluetooth® Compatibility...

Model Software Call Handling Enhanced Voice Control Phonebook Access Audio Streaming SMS Text Messaging
  • Compatible - The tested phone and software version is compatible with the Bluetooth® function listed.
  • Partially Compatible - The tested phone and software version may only partially function with the Bluetooth® function listed.
  • Not Compatible - The tested phone and software version is not compatible with the Bluetooth® function listed.
  • Text Message - Feature available with Apple CarPlay® and Android® Auto.
iPod, iPhone and Apple CarPlay are registered trademark of Apple Inc. Android is a registered trademark of Google Inc.

Important Information

The smartphones listed have been tested for compatibility with vehicles fitted with Holden Mylink by a third party under controlled conditions. Performance of your smartphone in Holden vehicles may vary in the future based on smartphone software versions and network coverage, therefore this information should be used as a guide only. If your smartphone supports Bluetooth® but is not listed on the website, this simply means it has not been tested for compatibility. However, there is a possibility that some of the Bluetooth® features may still work, but neither partial nor full functionality can be assured.

For these reasons please consult your local Holden Dealership or call Holden Customer Care on 1800 GM Holden (1800 46 465 336) if you require further information. Please note that smartphones are warranted by their manufacturer, not Holden.

Things you need to know

How can we improve this Tutorial?

We will endeavour to get back to you if possible

What do you need help with?

e.g. My bluetooth doesn't connect, and I keep getting an error mesage 404 on my phone.

Thank You

We appreciate your feedback.